An air brake is a conveyance braking system actuated by compressed air. The Westinghouse system uses air pressure to charge air reservoirs
(tanks) on each car. Full air pressure signals each car to release the
brakes. A reduction or loss of air pressure signals each car to apply
its brakes, using the compressed air in its reservoirs.
In order to design a system without the shortcomings of the straight air system, Westinghouse invented a system wherein each piece of railroad rolling stock was equipped with an air reservoir and a triple valve, also known as a control valve.
The triple valve is described as being so named as it performs three functions: Charging air into an air tank ready to be used, applying the brakes, and releasing them. In so doing, it supports certain other actions (i.e. it 'holds' or maintains the application and it permits the exhaust of brake cylinder pressure and the recharging of the reservoir during the release). In his patent application, Westinghouse refers to his 'triple-valve device' because of the three component valvular parts comprising it: the diaphragm-operated poppet valve feeding reservoir air to the brake cylinder, the reservoir charging valve, and the brake cylinder release valve. When he soon improved the device by removing the poppet valve action, these three components became the piston valve, the slide valve, and the graduating valve.
Under the Westinghouse system, therefore, brakes are applied by reducing train line pressure and released by increasing train line pressure. The Westinghouse system is thus fail safe—any failure in the train line, including a separation ("break-in-two") of the train, will cause a loss of train line pressure, causing the brakes to be applied and bringing the train to a stop, thus preventing a runaway train.
In addition, an emergency application brings in an additional component of each car's air brake system: the emergency portion. The triple valve is divided into two portions: the service portion, which contains the mechanism used during brake applications made during service reductions, and the emergency portion, which senses the immediate, rapid release of train line pressure. In addition, each car's air brake reservoir is divided into two portions—the service portion and the emergency portion—and is known as the "dual-compartment reservoir”. Normal service applications transfer air pressure from the service portion to the brake cylinder, while emergency applications cause the triple valve to direct all air in both the service portion and the emergency portion of the dual-compartment reservoir to the brake cylinder, resulting in a 20–30% stronger application.
The emergency portion of each triple valve is activated by the extremely rapid rate of reduction of train line pressure. Due to the length of trains and the small diameter of the train line, the rate of reduction is high near the front of the train (in the case of an engine operator-initiated emergency application) or near the break in the train line (in the case of the train line coming apart). Farther away from the source of the emergency application, the rate of reduction can be reduced to the point where triple valves will not detect the application as an emergency reduction. To prevent this, each triple valve's emergency portion contains an auxiliary vent port, which, when activated by an emergency application, also locally vents the train line's pressure directly to atmosphere. This serves to propagate the emergency application rapidly along the entire length of the train.
Passenger trains have had for a long time a 3-wire version of the electro-pneumatic brake, which gives seven levels of braking force. In most cases the system is not fail-safe, with the wires being energized in sequence to apply the brakes, but the conventional automatic air brake is also provided to act as a fail safe, and in most cases can be used independently in the event of a failure of the EP brakes.
. On the conventional side, the control valve set a reference pressure in a volume, which set brake cylinder pressure via a relay valve. On the electric side, pressure from a second straight-air trainline controlled the relay valve via a two-way check valve. This "straight air" trainline was charged (from reservoirs on each car) and released by magnet valves on each car, controlled electrically by a 3 wire trainline, in turn controlled by an "electro-pneumatic master controller" in the controlling locomotive. This controller compared the pressure in the straight air trainline with that supplied by a self lapping portion of the engineers valve, signaling all of the "apply" or "release" magnets valves in the train to open simultaneously, changing the pressure in the "straight air" trainline much more rapidly and evenly than possible by simply supplying air directly from the locomotive. The relay valve was equipped with four diaphragms, magnet valves, electric control equipment, and an axle-mounted speed sensor, so that at speeds over 60 mph (97 km/h) full braking force was applied, and reduced in steps at 60 mph (97 km/h) 40 and 20 mph (64 and 32 km/h), bringing the train to a gentle stop. Each axle was also equipped with anti-lock brake equipment. The combination minimized braking distances, allowing more full-speed running between stops. The "straight air" (electro-pneumatic trainline), anti-lock, and speed graduating portions of the system were not dependent on each other in any way, and any or all of these options could be supplied separately.
Later systems replace the automatic air brake with an electrical wire (in the UK, at least, known as a "round the train wire") that has to be kept energized to keep the brakes off.
Limitations
The Westinghouse air brake system is very trustworthy, but not infallible. Recall that the car reservoirs recharge only when the brake pipe pressure is higher than the reservoir pressure, and that the car reservoir pressure will rise only to the point of equilibrium. Fully recharging the reservoirs on a long trian can require considerable time (8 to 10 minutes in some cases), during which the brake pipe pressure will be lower than locomotive reservoir pressure.
If the brakes must be applied before recharging has been completed, a larger brake pipe reduction will be required in order to achieve the desired amount of braking effort, as the system is starting out at a lower point of equilibrium (lower overall pressure). If many brake pipe reductions are made in short succession ("fanning the brake" in railroad slang), a point may be reached where car reservoir pressure will be severely depleted, resulting in substantially reduced brake cylinder piston force, causing the brakes to fail. On a descending grade, the unfortunate result will be a runaway.
In the event of a loss of braking due to reservoir depletion, the engine driver may be able to regain control with an emergency brake application, as the emergency portion of each car's dual-compartment reservoir should be fully charged—it is not affected by normal service reductions. The triple valves detect an emergency reduction based on the rate of brake pipe pressure reduction. Therefore, as long as a sufficient volume of air can be rapidly vented from the brake pipe, each car's triple valve will cause an emergency brake application. However, if the brake pipe pressure is too low due to an excessive number of brake applications, an emergency application will not produce a large enough volume of air flow to trip the triple valves, leaving the engine driver with no means to stop the train.
Since the main reservoir pipe is kept constantly pressurized by the locomotive, the car reservoirs can be charged independently of the brake pipe, this being accomplished via check valve to prevent backfeeding into the pipe. This arrangement helps to reduce the above described pressure loss problems, and also reduces the time required for the brakes to release, since the brake pipe only has to recharge itself.
Main reservoir pipe pressure can also be used to supply air for auxiliary systems such as pneumatic door operators or air suspension. Nearly all passenger trains (all in the UK and USA), and many freights, now have the two-pipe system.
Straight air brake
In the air brake's simplest form, called the straight air system, compressed air pushes on a piston in a cylinder. The piston is connected through mechanical linkage to brake shoes that can rub on the train wheels, using the resulting friction to slow the train. The mechanical linkage can become quite elaborate, as it evenly distributes force from one pressurized air cylinder to 8 or 12 wheels.
The pressurized air comes from an air compressor in the locomotive and is sent from car to car by a train line made up of pipes beneath each car and hoses between cars. The principal problem with the straight air braking system is that any separation between hoses and pipes causes loss of air pressure and hence the loss of the force applying the brakes. This could easily cause a runaway train. Straight air brakes are still used on locomotives, although as a dual circuit system, usually with each truck having its own circuit.
Westinghouse air brakeIn order to design a system without the shortcomings of the straight air system, Westinghouse invented a system wherein each piece of railroad rolling stock was equipped with an air reservoir and a triple valve, also known as a control valve.
The triple valve is described as being so named as it performs three functions: Charging air into an air tank ready to be used, applying the brakes, and releasing them. In so doing, it supports certain other actions (i.e. it 'holds' or maintains the application and it permits the exhaust of brake cylinder pressure and the recharging of the reservoir during the release). In his patent application, Westinghouse refers to his 'triple-valve device' because of the three component valvular parts comprising it: the diaphragm-operated poppet valve feeding reservoir air to the brake cylinder, the reservoir charging valve, and the brake cylinder release valve. When he soon improved the device by removing the poppet valve action, these three components became the piston valve, the slide valve, and the graduating valve.
- If the pressure in the train line is lower than that of the reservoir, the brake cylinder exhaust portal is closed and air from the car's reservoir is fed into the brake cylinder to apply the brakes. This action continues until equilibrium between the brake pipe pressure and reservoir pressure is achieved. At that point, the airflow from the reservoir to the brake cylinder is lapped off and the cylinder is maintained at a constant pressure.
- If the pressure in the train line is higher than that of the reservoir, the triple valve connects the train line to the reservoir feed, causing the air pressure in the reservoir to increase. The triple valve also causes the brake cylinder to be exhausted to the atmosphere, releasing the brakes.
- As the pressure in the train line and that of the reservoir equalize, the triple valve closes, causing the air pressure in the reservoir and brake cylinder to be maintained at the current level.
Under the Westinghouse system, therefore, brakes are applied by reducing train line pressure and released by increasing train line pressure. The Westinghouse system is thus fail safe—any failure in the train line, including a separation ("break-in-two") of the train, will cause a loss of train line pressure, causing the brakes to be applied and bringing the train to a stop, thus preventing a runaway train.
Modern systems
Modern air brake systems serve two functions:- The service brake system, which applies and releases the brakes during normal operations, and
- The emergency brake system, which applies the brakes rapidly in the event of a brake pipe failure or an emergency application by the engine operator (generally referred to as the automatic brake).
In addition, an emergency application brings in an additional component of each car's air brake system: the emergency portion. The triple valve is divided into two portions: the service portion, which contains the mechanism used during brake applications made during service reductions, and the emergency portion, which senses the immediate, rapid release of train line pressure. In addition, each car's air brake reservoir is divided into two portions—the service portion and the emergency portion—and is known as the "dual-compartment reservoir”. Normal service applications transfer air pressure from the service portion to the brake cylinder, while emergency applications cause the triple valve to direct all air in both the service portion and the emergency portion of the dual-compartment reservoir to the brake cylinder, resulting in a 20–30% stronger application.
The emergency portion of each triple valve is activated by the extremely rapid rate of reduction of train line pressure. Due to the length of trains and the small diameter of the train line, the rate of reduction is high near the front of the train (in the case of an engine operator-initiated emergency application) or near the break in the train line (in the case of the train line coming apart). Farther away from the source of the emergency application, the rate of reduction can be reduced to the point where triple valves will not detect the application as an emergency reduction. To prevent this, each triple valve's emergency portion contains an auxiliary vent port, which, when activated by an emergency application, also locally vents the train line's pressure directly to atmosphere. This serves to propagate the emergency application rapidly along the entire length of the train.
Working pressures
The compressor on the locomotive charges the main reservoir with air at 125–140 psi (8.6–9.7 bar; 860–970 kPa). The train brakes are released by admitting air to the train pipe through the engineer's brake valve. A fully charged brake pipe is typically 70–90 psi (4.8–6.2 bar; 480–620 kPa) for freight trains and 110 psi (7.6 bar; 760 kPa) for passenger trains. The brakes are applied when the engineer moves the brake handle to the "service" position, which causes a reduction in pressure in the train pipe. In normal braking, the pressure in the train pipe does not reduce to zero.Enhancements
Electro-pneumatic or EP brakes are a type of air brake that allows for immediate application of brakes throughout the train instead of the sequential application. Electro-pneumatic brakes are currently in testing in North America and South Africa in captive service ore and coal trains.Passenger trains have had for a long time a 3-wire version of the electro-pneumatic brake, which gives seven levels of braking force. In most cases the system is not fail-safe, with the wires being energized in sequence to apply the brakes, but the conventional automatic air brake is also provided to act as a fail safe, and in most cases can be used independently in the event of a failure of the EP brakes.
. On the conventional side, the control valve set a reference pressure in a volume, which set brake cylinder pressure via a relay valve. On the electric side, pressure from a second straight-air trainline controlled the relay valve via a two-way check valve. This "straight air" trainline was charged (from reservoirs on each car) and released by magnet valves on each car, controlled electrically by a 3 wire trainline, in turn controlled by an "electro-pneumatic master controller" in the controlling locomotive. This controller compared the pressure in the straight air trainline with that supplied by a self lapping portion of the engineers valve, signaling all of the "apply" or "release" magnets valves in the train to open simultaneously, changing the pressure in the "straight air" trainline much more rapidly and evenly than possible by simply supplying air directly from the locomotive. The relay valve was equipped with four diaphragms, magnet valves, electric control equipment, and an axle-mounted speed sensor, so that at speeds over 60 mph (97 km/h) full braking force was applied, and reduced in steps at 60 mph (97 km/h) 40 and 20 mph (64 and 32 km/h), bringing the train to a gentle stop. Each axle was also equipped with anti-lock brake equipment. The combination minimized braking distances, allowing more full-speed running between stops. The "straight air" (electro-pneumatic trainline), anti-lock, and speed graduating portions of the system were not dependent on each other in any way, and any or all of these options could be supplied separately.
Later systems replace the automatic air brake with an electrical wire (in the UK, at least, known as a "round the train wire") that has to be kept energized to keep the brakes off.
Limitations
The Westinghouse air brake system is very trustworthy, but not infallible. Recall that the car reservoirs recharge only when the brake pipe pressure is higher than the reservoir pressure, and that the car reservoir pressure will rise only to the point of equilibrium. Fully recharging the reservoirs on a long trian can require considerable time (8 to 10 minutes in some cases), during which the brake pipe pressure will be lower than locomotive reservoir pressure.
If the brakes must be applied before recharging has been completed, a larger brake pipe reduction will be required in order to achieve the desired amount of braking effort, as the system is starting out at a lower point of equilibrium (lower overall pressure). If many brake pipe reductions are made in short succession ("fanning the brake" in railroad slang), a point may be reached where car reservoir pressure will be severely depleted, resulting in substantially reduced brake cylinder piston force, causing the brakes to fail. On a descending grade, the unfortunate result will be a runaway.
In the event of a loss of braking due to reservoir depletion, the engine driver may be able to regain control with an emergency brake application, as the emergency portion of each car's dual-compartment reservoir should be fully charged—it is not affected by normal service reductions. The triple valves detect an emergency reduction based on the rate of brake pipe pressure reduction. Therefore, as long as a sufficient volume of air can be rapidly vented from the brake pipe, each car's triple valve will cause an emergency brake application. However, if the brake pipe pressure is too low due to an excessive number of brake applications, an emergency application will not produce a large enough volume of air flow to trip the triple valves, leaving the engine driver with no means to stop the train.
Solutions
Two-pipe air brake
Another solution to loss of brake pressure is the two-pipe system, fitted on most modern passenger stock and many freight wagons. In addition to the traditional brake pipe, this enhancement adds the main reservoir pipe, which is continuously charged with air directly from the locomotive's main reservoir. The main reservoir is where the locomotive's air compressor output is stored, and is ultimately the source of compressed air for all systems that use it.Since the main reservoir pipe is kept constantly pressurized by the locomotive, the car reservoirs can be charged independently of the brake pipe, this being accomplished via check valve to prevent backfeeding into the pipe. This arrangement helps to reduce the above described pressure loss problems, and also reduces the time required for the brakes to release, since the brake pipe only has to recharge itself.
Main reservoir pipe pressure can also be used to supply air for auxiliary systems such as pneumatic door operators or air suspension. Nearly all passenger trains (all in the UK and USA), and many freights, now have the two-pipe system.
No comments:
Post a Comment